The Essentials For Your Day Pack

Always Carry The Right Gear

On a warm afternoon in July, a family leaves a trail head with the goal of summiting the South Sister Mountain in Central Oregon.  It was a rough hike as they took a path not frequently traveled.  By evening it became obvious that this group would not make it to the summit and the glacier they were attempting to cross was icing up; it just wasn’t safe to press on.  911 was called and a local SAR team reached them after midnight.  The temperature on the glacier dropped below 40° (F) and the hikers were getting cold.

When the SAR team reached them, they found that the group had some food and water but no other gear.  The hikers’ clothing selection was questionable too.

So what is the right stuff to carry in the outdoors?  What is the minimum?  What should you consider before hitting the trail?

A climbing group in the 1930s, The Mountaineers from Seattle authored the “Ten Essentials” describing ten items that should be carried in the back country. 

“The Ten Essentials” has been modified by different groups over the years.  The following is the list that REI recommends:

1. Navigation
2. Sun protection
3. Insulation (extra clothing)
4. Illumination
5. First-aid supplies
6. Fire
7. Repair kit and tools
8. Nutrition (extra food)
9. Hydration (extra water)
10. Emergency shelter
1. A space blanket is fine to carry but it is a poor shelter.

This is the minimum that one should carry; it is a starting point.  The key is to always carry your kit with you.  I have a day hiking kit that fits into a fanny pack.  It is only limited by its poor ability to carry extra clothing.

Accurate Compass Readings

I found these recommendations a while back when I was researching techniques for using a magnetic compass.  A small error when using a compass can result in significant error in measurement on the ground.

To obtain accurate readings when using a compass:

• Ensure the compass has been adjusted for declination. 
• Hold the compass level and steady so the needle swings freely.
• Hold the compass about waist high in front of the body, except when using a compass with a sighting mirror or a sighting type compass.
• Raise and lower eyes when taking a bearing, do not move your head. Always use the same eye when taking bearings.
• Directly face the object that is being measured.
• Magnetic fields will give incorrect compass readings. Avoid taking readings near magnetic fields such as steel, iron (ferrous metals), vehicles, rebar, and clipboards. Even belt buckles, glasses, and rings can interfere with the compass reading.
• Take bearings twice. 
• Adjust for magnetic declination as appropriate.
• Follow the direction of travel arrow, not the compass needle, when walking a bearing. Always follow the line indicated by the compass rather than relying on judgment as to the direction.
• Use back bearings to ensure you are on track when navigating.
  

  
• Compare compass reading with those of your GPS.
• Remember that a GPS receiver's compass must be calibrated after every battery change.

More About Using a Topographic Map

Reviewing a topographic map is usually the starting point for the planning of any back country trip.  A topographic map is your road map to the outdoors.  It provides you detailed information at a scale that is meaningful and detailed.  For years, the US Geologic Survey (USGS) has been the principal publisher of accurate maps.  Within the last decade we have seen many innovations in mapping products that include new mapping companies and publishers, software, maps for the GPS, and “Apps” for the iPhone. Outdoor Quest/Blake Miller image Still, the USGS map remains the standard for back country navigation (visit the USGS’s site at www.topomaps.usgs.gov.)   I’d also recommend looking at June Fleming’s “Staying Found” or Bjorn Kjellstrom’s “Be Expert With Map & Compass.”  Once you develop a map foundation you will easily shift to many of the other products on the market today.  Many publications, videos, and web sites will give you a te rundown on the features, symbols and components to a map.  This article will discuss a few of the key features that you should be aware on a 7.5 minute map. ·         Contour Lines These are the thin brown lines that snake across the map.  Contour lines connect equal points of elevation such that every point on that line will be at that elevation above sea level.  Visually, the contour lines give you a mental three dimensional view of the terrain.  These lines provide a view of slope and pitch, depressions, ridge lines and level ground; the highs and lows of the earth’s surface.  Outdoor Quest/Blake Miller image  These lines provide shape and a sense of texture. There are two primary types of lines, index and intermediate lines.  Index lines stand out as they are a touch wider, a darker shade of brown and indicate the elevation with numbers such as 4500; the elevation is in feet.  Between the index lines are the thin intermediate line that are spaced uniformly and further define the elevation, slope and contour.  The intervals between the intermediate lines are specified at the bottom of the map adjacent to the scale data. ·     Scale Consider scale as your view of the map; it is like your “overhead zoom” setting.  To cut to the chase, a 7.5 minute map or quadrangle has a scale that is referred to as 1:24,000; where one inch is equal to 2000 feet.  It is your best source of information of the back country.  At this scale, the map has much more validity and provides more usable information for your backcountry planning.  You can view important landmarks, streams and geographic features.  To complete the navigation picture I always refer a second map, such as a map of the national forest (e.g., the Deschutes National Forest.)  Commonly, such a map will be “zoomed” way out and have a scale of 1:100,000 or 1:250,000.  Imagine that such a map would be made up of many 7.5 minute quadrangles. ·    North  Features on a map such as trails, roads, mountain peaks and streams are all laid out in relation to true North; the North Pole.  The north-south borders of the map and the small declination diagram are your best references for true North.  Other grid lines (such as the red Township, Section and Range lines) may not be aligned to true north at all.  Be careful of these lines should you need to triangulate your position on a map. ·    Declination This is the angular difference between true North and Magnetic North.  The red needle on your magnetic compass points to Magnetic North.  The accuracy of the information found in the Declination Diagram is dependent on the age of the map.  To get the latest declination for any area visit www.magnetic-declination.com. Personally I use a magnetic compass that I can adjust for declination; it just makes my navigation easier.  When adjusted, my compass provides bearing information in degrees true as does my map and my adjusted GPS. ·    Coordinates Latitude and Longitude (Lat/Long) are the familiar coordinate system to most outdoorsmen and women.  Coordinate data is found at the top and bottom corners of each map.  Lat/Long coordinate increments are also found every 2’ (minutes) and 30” (seconds) on the sides of the Map.  A scaling device is necessary to pull complete coordinates off a map; this is a pain. In the 1940’s a coordinate system know as Universal Transverse Mercator (UTM) was developed.  To keep a very long story short, your 7.5 minute map has a new grid laid over it, the grid dimensions are 1000 meters by 1000 meters.  For more complete   information on UTM grid visit the USGS’s web site UTM or Lathem’s “GPS Made Easy” (which is probably at your local library.) Simplicity is the essence of UTM.  Scouts, hunters and hikers have joined Search and Rescue (SAR) teams around the country in using this system.  Your GPS receiver can easily be switched to UTM from the set-up menu. ·    Bar Scales   Notice the bar scales at the bottom of the 7.5 minute map.  The scales provide measuring data in miles, feet and meters.   On the far left side of the meter scale, the scale is broken down into units of 100 meters, this applies directly to UTM. Notice on the scale bar (feet) that 1 inch equals 2000 feet. ·    Map Datum Information about map datum is found in the lower left corner of a 7.5 minute map.  I have found that the simplest definition from GPS maker Garmin is: “A math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum. The map datum selected on a GPS receiver needs to match the datum listed on the corresponding paper map in order for position readings to match.” The bottom line: most 7.5 minute maps are made to the North American datum of 1927 (NAD27 or NAD27 CONUS on your GPS).  New GPS receivers are set to datum WGS84.  The difference between the datum could be over 100 meters/yards.  The solution: When pulling points off a map shift your GPS’s datum to match the map.  If precision is not an issue for your outing don’t worry about datum. As you begin your trip planning don’t forget the magnetic compass, the important partner to any topographic map.  See Selecting a magnetic Compass for more information about buying a good compass. Visit www.caltopo.com for free topographic maps of the Continental US.  This is a super mapping program that you can use to explore your area and print them at home.

Free GPS Maps

There are several sources of Maps for your GPS receiver.

In the free category I like and use maps from www.GPSFileDepot.com. 

ONYXmaps.com maps are not free but the quality is just superb.  GARMIN has fine maps too but you will have to pay for them.

Do let me know if you have a free map source that are really good.

Topo Map Bassics

Reviewing a topographic map is usually the starting point for the planning of any back country trip.  A topographic map is your road map to the outdoors.  It provides you information at a scale that is meaningful and detailed.  

For years, the US Geologic Survey (USGS) has been the principal publisher of accurate maps.  Within the last decade we have seen many innovations in mapping products that include new mapping companies and publishers, software, maps for the GPS, and “Apps” for the smart phone.

Still, the USGS map remains the standard for back country navigation (visit the USGS’s site at www.topomaps.usgs.gov.)   I’d also recommend looking at June Fleming’s “Staying Found” or Bjorn Kjellstrom’s “Be Expert With Map & Compass.”  Once you develop a map foundation you will easily shift to many of the other products on the market today. 

Many publications, videos, and web sites will give you a complete rundown on the features, symbols and components to a map.  The key features that you should be aware of are:

·         Contour Lines These are the thin brown lines that snake across the map.  Contour

lines connect equal points of elevation such that every point on a specific line will be at that elevation above sea level.  Visually, the contour lines give you a mental three dimensional view of the terrain.  These lines provide shape and a sense of texture.  Contour lines provide a view of slope and pitch, depressions, ridge lines and level ground; the highs and lows of the earth’s surface.  There are two primary types of lines, index and intermediate lines.  Index lines stand out as they are a touch wider, a darker shade of brown and indicate the elevation with numbers such as 4500; the elevation is in feet.  Between the index lines are the thin intermediate line that are spaced uniformly and further define the elevation, slope and contour.  The distance intervals between the intermediate lines are specified at the bottom of the map adjacent to the scale data.

·         Scale Consider scale as your view of the map; it is like your “overhead zoom” setting.  To cut to the chase, a 7.5 minute map or quadrangle has a scale that is referred to as 1:24,000; where one inch is equal to 2000 feet.  It is your best source of information of the back country.  At this scale, the map has much more validity and provides more usable information for your backcountry planning.  You can view important landmarks, streams and geographic features.  To complete the navigation picture I always refer a second map, such as a map of the national forest (e.g., the Deschutes National Forest.)  Commonly, such a map will be “zoomed” way out and have a scale of 1:100,000 or 1:250,000.  Imagine that such a map would be made up of many 7.5 minute quadrangles.

·         North  Features on a map such as trails, roads, mountain peaks and streams are all laid out in relation to true North; the North Pole.  The north-south borders of the map and the small declination diagram are your best references for true North.  Other grid lines (such as the red Township, Section and Range lines) may not be aligned to true north at all.  Be careful of these lines should you need to triangulate your position on a map.

·         Declination This is the angular difference between true North and Magnetic North.  The red needle on your magnetic compass points to Magnetic North.  The accuracy of the information found in the Declination Diagram is dependent on the age of the map.  To get the latest declination for any area visit www.magnetic-declination.com.

Personally I use a magnetic compass that I can adjust for declination; it just makes my navigation easier.  When adjusted, my compass provides bearing information in degrees true as does my map and my adjusted GPS.

·         Coordinates Latitude and Longitude (Lat/Long) are the familiar coordinate system to most outdoorsmen and women.  Coordinate data is found at the top and bottom corners of each map.  Lat/Long coordinate increments are also found every 2’ (minutes) and 30” (seconds) on the sides of the Map.  A scaling device is necessary to pull complete coordinates off a map; this is a pain.

In the 1940’s a coordinate system known as Universal Transverse Mercator (UTM) was developed.  To keep a very long story short, your 7.5 minute map has a new grid laid over it, the grid dimensions are 1000 meters by 1000 meters.  For more complete information on UTM grid visit the USGS’s web site UTM or Letham’s “GPS Made Easy” (which is probably at your local library.)

Simplicity is the essence of UTM.  Scouts, hunters and hikers have joined Search and Rescue (SAR) teams around the country in using this system. 

Your GPS receiver can easily be switched to UTM from the set-up menu.

·         Bar Scales   Notice the bar scales at the bottom of the 7.5 minute map.  The scales provide measuring data in miles, feet and meters.   On the far left side of the meter scale, the scale is broken down into units of 100 meters, this applies directly to UTM.

Notice on the scale bar (feet) that 1 inch equals 2000 feet.

 Map Datum Information about map datum is found in the lower left corner of a 7.5 minute map.  I have found that the simplest definition from GPS maker Garmin is:

“A math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum. The map datum selected on a GPS receiver needs to match the datum listed on the corresponding paper map in order for position readings to match.”

The bottom line: most 7.5 minute maps are made to the North American datum of 1927 (NAD27 or NAD27 CONUS on your GPS).  New GPS receivers are set to datum WGS84.  The difference between the datum could be over 100 meters/yards.  The solution: When pulling points off a map shift your GPS’s datum to match the map. 

If precision is not an issue for your outing don’t worry about datum.

Visit www.worldofteaching.com/powerpoints/geography/Mapping.ppt.  This power point presentation offers a fine overview of topographic mapping.  It’s free.

GPS Tune-up for your fall hunt.

Hunters, this is a great time to tune-up and practice with a GPS receiver.  There are several things that one can do before leaving home.   Here are a few recommendations to consider.

Setup

• Dump those old AA batteries, put in new ones.  If you leave your GPS on all day in the

  

  Garmin Image

     field expect to change the batteries nightly.  Consider using lithium AA’s, they last longer and work better in cold temperatures. 

• “Match the map” with the receiver’s navigation selection options. Specifically, match the coordinate system (e.g., UTM or Latitude/Longitude) and map datum that are found on the map.  Consider shifting the receiver’s compass to degrees true.  Further, let’s have everyone in a hiking or hunting group use the same settings too; let’s all be on the same page.

•  Keep you navigation simple.  It’s easier to work with a handful of waypoints rather than list of 300.  Dump the Junk - Delete the old waypoints, the ones you will never use again.  Log important waypoints (e.g., that lake side camp site) on your PC or in a notebook.  Visit www.easygps.com or www.garmin.com for a place to store waypoints.

• Install maps on your GPS receiver.  Maps on the receiver are a natural complement to your paper field map.   Quality maps are available from onxmaps.com and GPSFiledepot.com (free).

• Adjust your map pages’ zoom setting to see what works best.  For general trail hiking I  keep my zoom setting at 800 feet.  This setting allows me to view trails, water sources, roads and elevation contours.

• Visit the manufacture’s web site to see if there are any firmware updates.  I do this every couple of months.

• When batteries are replaced calibrate the electronic compass.

Tune-up

• Verify that you are receiving enough satellite signals.  Check this on the satellite status screen.  Four satellites are the minimum.  Give older receivers the time to collect satellite data; don’t rush the navigation process.

• Give key waypoints names.  When marking a waypoint enter names like “camp” and “truck.”  It’s easier and more meaningful to find “truck” in the list of waypoints than is waypoint 542; or was it 245.  

·        After marking a waypoint, verify that it has been saved to the receiver's memory by checking either the map page or in the waypoint file (select “where to” or “find.”)  If the waypoint is on the map or in the list of waypoints, the hiker is ready to go.  If the waypoint is not found, start over.

·      

Outdoor Quest Image

 When it’s time to return to a destination chose “Where To” or “Find” on your keypad or menu.  Select the waypoint from the list provided.  Press the “Page” button and rotate through the many displays to the “Compass” page.  A large red arrow should appear on the face of the compass pointing to the selected waypoint.  When on course to the destination the arrow points to the top center of the receiver.  Practice this specific process at home before heading to the field.

• Navigation is a perishable skill.  I recommend that two weeks before an outing take the GPS receiver everywhere.  Add waypoints, delete waypoints and find a saved waypoint.  This process develops familiarization with the unit and allows the user to develop confidence with the receiver      and personal ability.

• Compliment GPS skills with a good review of map and compass fundamentals. Learn to back up electronic position fixing with bearing triangulation.   Worst case, a broken GPS becomes a paperweight for your map while afield.  For more information visit www.outdoorquest.blogspot.com .

·         When on the trail compare GPS position data with a map.  Compare what is presented electronically with what is on the map.

I suggest checking out Lawrence Letham’s book GPS Made Easy from the library.  This book compliments the owner’s manual.  An excellent reference for map and compass use is June Fleming’s Staying Found.

Taking a class can further enhance you GPS knowledge.  Classes are frequently offered through the local community college’s continuing education program or at local retailers such as  REI.

A map and compass always goes with me into the field.  I carry a Silva Ranger compass and get my maps from Caltopo.com  (their maps are free.)

Have fun while building on your fundamental navigation skill sets.  Consider setting up a treasure hunt or a geocach for a family get together.  Make it fun, make it simple and explain that these skills could one day make a huge difference if the ever got lost in the woods. 

Snakes

 The California Department of Fish and Wildlife (CDFW) is reminding the public to be rattlesnake safe. All of California is snake country. Much like bats, rattlesnakes are often misunderstood. They play an important role in the ecosystem by keeping rodent populations under control.

California has six venomous snakes, all of which are various species of rattlesnake. They are heavy-bodied, blunt-tailed with triangular-shaped heads. A rattle may not always be present, as they are often lost through breakage and not developed on the young. Additional species information can be found here.

Rattlesnakes are generally not aggressive and usually strike when threatened or provoked. Given room, they will retreat and want to be left alone. They are not confined to rural areas and have been found in urban environments, lakeside parks and golf courses.

The best protection against unwelcome rattlesnakes in the yard is to have a “rattlesnake-proof” fence. The fence should either be solid or with mesh no larger than one-quarter inch. It should be at least 3 feet high with the bottom buried a few inches in the ground.

Keep the fence clear of vegetation and debris. Encourage and protect kingsnakes, which prey on rattlesnakes, and other natural competitors like gopher snakes and racers.

On rare occasions, rattlesnakes can cause serious injury to humans. Most bites occur between the months of April and October when humans are most active outdoors. The California Poison Control Center notes that rattlesnakes account for more than 800 bites each year in the U.S. with one to two deaths. 

CDFW recommends the following outdoor safety precautions:

• Wear hiking boots and loose-fitting long pants.
• Never go barefoot or wear sandals when walking through wild areas.
• When hiking, stick to well-used trails.
• Avoid tall grass, weeds and heavy underbrush where snakes may hide during the day.
• Do not step or put your hands where you cannot see, and avoid wandering around in the dark.
• Step ON logs and rocks, never over them, and be especially careful when climbing rocks or gathering firewood.
• Remember, rattlesnakes can swim so never grab “sticks” or “branches” while swimming in lakes and rivers.
• Teach children to respect snakes and to leave them alone.

What to do in the event of a snake bite:

• Stay calm and wash the bite area gently with soap and water.
• Remove watches, rings, etc, which may constrict swelling.
• Immobilize the affected area and go to the nearest medical facility.

What you should NOT do after a rattlesnake bite:

• DON’T apply a tourniquet.
• DON’T pack the bite area in ice.
• DON’T cut the wound with a knife or razor.
• DON’T use your mouth to suck out the venom.
• DON’T let the victim drink alcohol. 

A great article on snake bites was published in Outside Magazine.